PRODUCTSSearch (1)
| KZ Type Air Permeability Tester [AP-500KZ-3A-D3, AP-200KZ-2A-D1] | |
|---|---|
 | Reference standard: JIS L 1096 ；ASTM D737 ；DIN 53887 ；BS 5636 standards |
| Appearance Retention Tester [ARP-100] | |
|---|---|
 | Reference standard: JIS L 1076 ； ASTM D3511 、D3512 standards |
| Warmth Retaining and Thermal Resistance Tester [ASTM-100B] | |
|---|---|
 | Reference standard: JIS L-1096 ASTM D1518-85 GB/T11048 -2008(B type method) |
| This equipment is used to determine the overall themal transmission coefficients due to the combined action of textile fabics, batting, and other materials. It meatures the time rate of heat tansfer from a warm constant-temperature, horizontal flat-plate up through the test material to a relatively calm, cool atmosphere. | |
| 【end of manufacture】 [BSM-100] |
|---|
| Reference standard: |
| Crock Meter [C-1（manual）, C-1D（motor driven）] | |
|---|---|
 | Reference standard: JIS L 0849 ISO 105-X12 GB/T 3920/1997 AATCC 8/2005 |
| This apparatus is a tester for determining the colour fast- ness to rubbing. A rubbing finger is a circular rubbing surface measuring 16mm in diameter. There are 2 models, the type to which rubbing finger is made to go and come back mnually, and the type by motor driven. | |
| Automatic Cantilever Softness Tester 【end of manufacture】 [CAN-1MCA] | |
|---|---|
 | Reference standard: JIS L 1096、JIS L 1018、JASO M403 standards |
| Automatic Cantilever Softness Tester [CAN-1MCC] | |
|---|---|
 | Reference standard: JIS L-1096、L-1912、L-1913 ISO 9073-7 ASTM D 5732 GB/T 18318-01 |
| This tester can measure stiffness properties of textile fabrics and nonwoven fabrics by employing the principle of cantilever bending of the fabric its own weight. | |
| Universal Textile Abrasion Tester [CAT-125A] | |
|---|---|
 | Reference standard: JIS L-1096、ASTM D3885、D3886、 |
| Accurate data of abrasion test of various materials, such as woven and knitted textiles, carpet, hosiery, felt paper, leather cloth, sheet and film, shall be obtained. By combining respective attachments, three types of test, of flat surface abrasion, bending abrasion and edge abrasion, may be executed. | |
| Thickness Gauge [CR-10A, FS-60DS] | |
|---|---|
 | Reference standard: JIS L 1096 ISO 5084 GB/T 3820 |
| This is an apparatus to measure the thickness of fiber cloth, film, paper, form rubber etc. With the presser at- tached to the botom end of the indication spindle the speci men is held fast and its thickness quickly measured. CR-10A type indicate the reading on the dial-gauge and FS-60DS type indicate the reading on the digital indication gauge. | |
| Dry Cleaning Tester [DC-1A, DC-2A] | |
|---|---|
 | Reference standard: JIS L 1018、JIS L 1089 、JIS L 1091standards |
| De Mattie Type Repeat Endurance Tester [DC-210（卓上型）, DC-310（床上型）] | |
|---|---|
 | Reference standard: JIS K 6260 ；ISO 132 standard |
| Baking Test Apparatus【end of manufacture】 [DK-1M] | |
|---|---|
 | Reference standard: |
| Dynamic Loading Tester (Slide-type) [DLT-100] | |
|---|---|
 | Reference standard: JIS L-1022、ISO 2094-1994 |
| Drape Tester 【end of manufacture】 [DRP-100, DRP-200] | |
|---|---|
 | Reference standard: JIS L 1096；JIS L 1018 standards |
| Dynamic Tearing-Puncture Tester 【end of manufacture】 [DTP-100] | |
|---|---|
 | Reference standard: JIS T-8050, ISO 13995 standards |
| Faraday-cage Electric Charge Tester [FEC-100] | |
|---|---|
 | Reference standard: JIS L 1094；JIS T 8118；ZB W 04008-89 standards |
| Flexo-Meter (With Freezer) [FOM-100C] | |
|---|---|
 | Reference standard: JIS K 6545; ISO 5402:2002 |
| Flexing Endurance Tester [FOM-120] | |
|---|---|
 | Reference standard: JIS K 6545 standards |
| Fabric Shift Tester [FS-1] | |
|---|---|
 | Reference standard: JIS L-1096、GB/T 13772.3standard |
| Surface Flash Burning Test Apparatus [FST-10A] | |
|---|---|
 | Reference standard: JIS L－1917 standard |
| Gurley Type Bending Stiffness Tester [GAS-10] | |
|---|---|
 | Reference standard: JIS L 1096；JAPAN TAPPI No.40 standards |
| Gurley Type Bending Stiffness Tester [GAS-100] | |
|---|---|
 | Reference standard: JIS L 1096；JAPAN TAPPI No.40 standards |
| Static Honest Meter（for Electrostatic Propensity） [H0110/V2] | |
|---|---|
 | Reference standard: JIS L 1094；GB/T 12703 |
| 【ACCESS.】 Power cord 1pc Signal cord 1pc Calibration tool &Blancer 1set Hex wrench 1pc 2A Fuse 1pc | |
| Bursting Strength Tester (Hydraulic method) 【end of manufacture】 [HB-1000K] | |
|---|---|
 | Reference standard: |
| Leather Iron Rubbing Tester [HLD-150] | |
|---|---|
 | Reference standard: |
| Strong Shaking Device [KS-100] | |
|---|---|
 | Reference standard: ISO1833 / 5088, JIS L1030-2 |
| Horizontal-Shaker Type Dyeing Tester 【end of manufacture】 [KS-12M, KS-17M] | |
|---|---|
 | Reference standard: |
| [KS-13S] | |
|---|---|
 | Reference standard: |
| Launder Meter [L-8Z, L-8Z-T, L-12Z, L-12Z-T, L-16Z, L-16Z-T, L-20Z, L-20Z-T] | |
|---|---|
 | Reference standard: JIS L 0844 ISO 105 AATCC 61-2006 GB／T 3921（1~5） |
| This apparatus is used mainly to estimate the colour fastness of dyed fabrics against washing. A specimen of the textile in contact with specified adjacent fabric is laundered, rinsed and dried. Specimens are laundered under appropriate onditions of temperature, bleachig and abrasive actiion such that the result is obtained in a short time. The abrasive action is ac- complished by the use of a low liquid ratio and an ap- propriate number of steel bals.The change in colour of the specimen and the staining of the adjacent fabric of fabrics are assessed by comparion with the grey scale. | |
| Light Blocking Effect Tester [LBC-10A] | |
|---|---|
 | Reference standard: JIS L-1055 standard |
| Twist Counter [M-1, MM-20] | |
|---|---|
 | Reference standard: JIS L-1095, ISO 2061 / 2062 / 6939, ASTM 1422 / 1423 |
| Moisture Regain Oven 【end of manufacture】 [MD-100] | |
|---|---|
 | Reference standard: JIS L 0105-5.3.2、L-1096-8.1 ASTM D-1576、D-2495-01 GB/T 5718-1997 |
| This oven with an electric balance is used for measuring the moisture content and regain percentage of textile materials. This oven is warmed by an infrared heater and conrolled by a temp.controller in the temperature range of 105±2℃ throughout the nclosure. | |
| Mullen Type Bursting Strength Tester [ML-100KG-PD] | |
|---|---|
 | Reference standard: JIS L－1096、1018；ISO 13938-1、2758、2759、3303； ASTM 3786；GB 7742 standards |
| Mullen Type Bursting Strength Tester [ML-711(容量：4500KPa), ML-721(容量：2000KPa)] | |
|---|---|
 | Reference standard: JIS L－1096 |
| Crease Recovery Tester of Woven Fabrics [MR-1] | |
|---|---|
 | Reference standard: |
| NK-type Pilling Tester [NK-100] | |
|---|---|
 | Reference standard: |
| Seam Strength Tester For Sweater [NRG-100] | |
|---|---|
 | Reference standard: |
| Pin-On-Disk Abrasion Tester [RD-100M] | |
|---|---|
 | Reference standard: JIS K-7218 (Testing Methods for Sliding Wear Resistance of Plasics) |
| This tester is equipment applicable to the B method of he slide wear test method (JIS Kー7218) of a plastic, and is mainly used for evaluation of the slide wear characteristics of a plasic material. | |
| Pin-On-Disk Abrasion Tester 【100A type end of manufacture】 [RD-100M, RD-100A] | |
|---|---|
 | Reference standard: JIS K-7218 (Testing Methods for Sliding Wear Resistance of Plasics) |
| This tester is equipment applicable to the B method of he slide wear test method (JIS Kー7218) of a plastic, and is mainly used for evaluation of the slide wear characteristics of a plasic material. | |
| Water Repellency Tester (Bundesmann Method) [RT-101A] | |
|---|---|
 | Reference standard: JIS L 1092；GB/T 14577；ISO 9865；BS EN 29865；DIN 53888standards |
| Uniform Abrasion Tester [SAT-310A] | |
|---|---|
 | Reference standard: JIS JIS L-1096 ASTM D-4158 |
| This apparatus is suitable for measuring the degree of wear strong of an extended sample like a knitting fabric. It is suitable for evaluation the abrasion strength mainly in the elbow, knee and inner side of the thigh of knitting fabric. The tester consists of an abrading, specimen supporting and driving mechanism. The surface of the abradant lies in a plane parallel to the surface supporing he specimen and presses upon the specimen. The abradant and specimen rotate in the same direction at very nealy but not quite the same angular velocity. | |
| Scott Type Crease-Flex Abrasion Tester [SCF-100, SCF-200] | |
|---|---|
 | Reference standard: JIS L-1096、K-6406-6 JASO M403 GMW3217 GB/T 8948-2008 standards |
| Simple－type Raising Tester [SD-110] | |
|---|---|
 | Reference standard: |
| Yarn-on-Yarn Abrasion Resistance Tester [SDI-510] | |
|---|---|
 | Reference standard: ASTM-6611 |
| Snag Tester [SG-1] | |
|---|---|
 | Reference standard: JIS L1058 standard C method |
| Textile Shrinkage Percentage Tester (Dip Method)【end of manufacture】 [SP-1E] | |
|---|---|
 | Reference standard: |
| Spray Tester [SR-1] | |
|---|---|
 | Reference standard: JIS L 1092 standard |
| Wrap Reel by Motor Driven [SSD-1, SSD-2, SSD-3] | |
|---|---|
 | Reference standard: |
| TO Type Pilling Tester [TO-100A] | |
|---|---|
 | Reference standard: JIS L 1076 standard B method |
| Thermal Shrinkage-Force Tester [TS-10FA] | |
|---|---|
 | Reference standard: ASTM D4974－01 standard |
| Scorch-Iron Tester [TSI-100B] | |
|---|---|
 | Reference standard: JIS L 0850、JIS L 0879 ISO 105－X11、ISO 105－P01 AATCC 92、AATCC 117 GB/T 6152、GB/T 5718 |
| This tester is used to dtermine the potential damage caused by retained chlorine. In addition to this testing, it is adapted also for determining the resistance of the colour of textiles of all kinds and in all forms to the action of dry heat. Heating device, consisting of a pair of smooth parallel plates, equipped with an accurately controllable electrical heating system and giving a pressure on the specimen of 4 kPa±1 kPa. | |
| Seamed Line Fatigue Tester [TTD-100] | |
|---|---|
 | Reference standard: |
| High-Pressure Type Water Resistance Tester [WP-1000K] | |
|---|---|
 | Reference standard: JIS L 1092、ISO 811、AATCC 127、GB/T 4744 standards |
| Hand-operated Water Resistance Tester [WP-1M] | |
|---|---|
 | Reference standard: |
| Schopper Type Water Penetration Tester 【DM type end of manufacture】 [WR-1600DM, WR-2000DM, WR-1600M, WR-2000M] | |
|---|---|
 | Reference standard: JIS L 1092；ISO 811；AATCC 127；GB/T 4744 |
| Schopper Type Water Penetration Tester [WR-1600M, WR-2000M] | |
|---|---|
 | Reference standard: JIS L 1092；ISO 811；AATCC 127；GB/T 4744 |
| Test Washer Apparatus（Washer Method）【end of manufacture】 [WS-1SE] | |
|---|---|
 | Reference standard: JIS L 1096, JIS L 1018 |